Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
Were you trying to locate insight about Tools You Need to Install a New Bathtub ?
Setting up a tub isn't specifically brain surgery, yet it does need strong plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably tough task. If the old tub is readily easily accessible, the task can relocate immediately; if you need to open up a wall surface to get rid of the old tub and position the brand-new bathtub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly need a helper to leave the old tub and also set in the brand-new one. Make sure you have qualified yourself for the job as well as are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed job, it is much better to think about utilizing one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This post will certainly help you install a new bathtub in your bathroom if you have actually currently bought a brand-new tub and don't need to transform the setup of your previous water pipes.
Your tools and material list ought to comprise the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid strain on the bath tub.
Fit the versatile faucet adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final placement.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you need to do is detach the water. After doing so, activate the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the limited access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the staying water that will certainly come from the pipes. When the supply pipelines have actually been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before moving on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using the two wood boards under its feet, position the tub in the called for placement. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the spirit level checks out level.
To set up faucets, fit the bottom of the outermost versatile tap adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water supply as well as check all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub and also examine the overflow outlet as well as the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has actually been made use of at least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in location in between the faucet and the sink. Safeguard the tap in place with the supplier supplied backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former kind must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, resulting in problems with dampness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture rather early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very enthusiastic about How to Install a Bathtub Yourself and I'm hoping you appreciated our page. If you enjoyed reading our blog post plz do not forget to share it. Thanks a bunch for your time. Don't hesitate to stop by our blog back soon.
We're here 24/7, call! Report this page